蒲公英 - 制药技术的传播者 GMP理论的实践者

搜索
查看: 2851|回复: 5
收起左侧

【非原创】多肽合成技巧

[复制链接]
药徒
发表于 2014-10-14 11:39:09 | 显示全部楼层 |阅读模式

欢迎您注册蒲公英

您需要 登录 才可以下载或查看,没有帐号?立即注册

x
N末端的生物素标记
Wash 0.1 mmol resin with DMF.
Dissolve 0.244 g (+)-biotin (1 mmol, MW 244.3) in 5 mL DMF-DMSO (1:1) solution. A little warming is necessary.
Add 2.1 mL 0.45 M HBTU/HOBt solution and 0.3 mL DIEA to the solution prepared in step 2.
Add the activated biotin solution to the resin and let stir overnight.
Check resin to make sure coupling is complete as evidenced by negative ninhydrin test (colorless).
Wash resin with DMF-DMSO (1:1) (2x) to remove excess (+)-biotin.
Wash resin with DMF (2x) and DCM (2x).
Let the resin dry before proceeding to cleavage.
在2-氯TRT树脂上挂第一个FMOC氨基酸的方法
Weigh 10 g 2-chlorotrityl chloride resin (15 mmol) in a reaction vessel, wash with DMF (2x), swell the resin in 50 mL DMF for 10 min, drain vessel.
Weigh 10 mmol Fmoc-amino acid in a test tube, dissolve Fmoc-amino acid in 40 mL DMF, transfer the solution into the reaction vessel above, add 8.7 mL DIEA (50 mmol), swirl mixture for 30 min at room temperature.
Add 5 mL methanol into the reaction vessel and swirl for 5 min.
Drain and wash with DMF (5x).
Check substitution.
Add 50 mL 20% piperidine to remove the Fmoc group. Swirl mixture for 30 min.
Wash with DMF (5x), DCM (2x), put resin on tissue paper over a foam pad and let dry at room temperature overnight under the hood. Cover the resin with another piece of tissue paper, press lightly to break aggregates.
Weigh loaded resin.
Pack in appropriate container.
检测树脂上面是否挂上第一个FMOC氨基酸的方法
Weigh duplicate samples of 5 to 10 mg loaded resin in an eppendorf tube, add 1.00 mL 20% piperidine/DMF, shake for 20 min, centrifuge down the resin.
Transfer 100 ?L of the above solution into a tube containing 10 mL DMF, mix well.
Pipette 2 mL DMF into each of the two cells (reference cell and sample cell), set spectrophotometer to zero. Empty the sample cell, transfer 2 mL of the solution from step 2 into the sample cell, check absorbance.
Subs = 101(A)/7.8(w)
A = absorbance
w = mg of resin
Check absorbance three times at 301 nm, calculate average substitution.
FMOC方法合成多肽操作步骤 (0.25 mmol)
Wash resin with DMF (4x) and then drain completely.
Add approximately 10 mL 20% piperidine/DMF to resin. Shake for one min and drain.
Add another 10 mL 20% piperidine/DMF. Shake for 30 min.
Drain reaction vessel and wash resin with DMF (4x). Make sure there is no piperidine remaining. Check beads using ninhydrin test, beads should be blue.
Coupling Step - Prepare the following solution:
1 mmol Fmoc-amino acid
2.1 mL 0.45 M HBTU/HOBT (1mmol)
348 ?L DIEA (2 mmol)
Add above solution to the resin and shake for a minimum of 30 min. This coupling step can be longer if desired.
Drain reaction vessel and wash resin with DMF (4x).
Perform Ninhydrin test:
If negative (colorless), proceed to step 2 and continue synthesis.
If positive (blue), return to step 5 and re-couple the same Fmoc-amino acid. Increase the coupling time if necessary.
合成含有磷酸化酪氨酸多肽的方法
Reagent: N-a-Fmoc-O-phosphotyrosine
For 0.1 mmol or 0.25 mmol synthesis, use 0.483 g Fmoc-Tyr(PO3H2)-OH (1 mmol, MW 483.4) . For ABI synthesizers, pack Fmoc-Tyr(PO3H2)-OH in a cartridge.
The cycle program for coupling Fmoc-Tyr (PO3H2)-OH is the same as for other Fmoc-amino acids except for the coupling time (see step 3). (Note: ABI synthesizers use HBTU/HOBT as the activating reagent.)
The coupling time for Fmoc-Tyr(PO3H2)-OH needs to be increased. For ABI model 430A peptide synthesizer, insert several steps (i.e., vortex on, wait 990 sec, vortex off, to increase the coupling time). For ABI model 431A peptide synthesizer, add additional "I"s. Overnight coupling may be necessary for some sequences.
After the coupling step for Fmoc-Tyr(PO3H2)-OH, perform ninhydrin test to ensure complete coupling. Negative (colorless) ninhydrin test indicates complete coupling, while a positive (blue) ninhydrin test indicates incomplete coupling.
Increase the coupling time of the amino acid residues after the phosphotyrosine or perform double coupling. (Note: The coupling of amino acids after the phosphotyrosine can be difficult.)
There is a limit on the number of amino acid residues that can be coupled after the hosphotyrosine. Since the phospho group is unprotected, side reactions are likely to ccur. (Note: Peptides have been successfully coupled with sequences containing up o ten additional amino acids following the phosphotyrosine residue.)
用Wang树脂和2-氯TRT树脂同时合成多肽
Peptides which differ in the C-termini can be simultaneously synthesized in one reaction vessel by employing resins that possess different cleavage properties. The resins used were the weak acid labile 2-chlorotrityl resins and the TFA labile Wang resins. The success of this approach was shown by the co-synthesis of ACTH (4-10) with ACTH (4-11) and Neuropeptide Y, a C-terminal amide peptide with its corresponding C-terminal free acid analog.
*Hong A., Le T., and Phan T. Techniques in Protein Chemistry VI, 531-562 (1995).
切割程序
Starting Resin: Chlorotrityl resins
Reagents for 1 g Peptide-Resin:
1 mL acetic acid (AcOH)
2 mL trifluoroethanol (TFE)
7 mL dichloromethane (DCM)
Prepare above mixture.
Add peptide-resin to the mixture and let it stir at room temperature for 1 h.
Filter and wash resin with 10 mL TFECM (2:8) (2x) to ensure that all of the product is recovered.
Evaporate the solvent until there is less than 5 mL of liquid.
Add ether to a test tube containing about 100 mL of the above solution. Check solubility of the fully protected peptide in ether. If the product precipitates, proceed to step 6. If no precipitate is observed, proceed to step 7.
Add cold ether to the residual liquid in step 4 to precipitate the fully protected peptide. Filter through a fine sintered funnel to obtain the product.
Some fully protected peptides are soluble in ether. In this case, add water to precipitate them out. Filter through a fine sintered funnel to obtain the product.
从Fmoc-Lys(Mtt)氨基酸上脱去Mtt的方法
Reagent:
Fmoc-Lys(Mtt)-OH
Swell resin in DCM.
Wash resin with 3% TFA/DCM (2x) (since the resin is swollen in DCM, this step of washing the resin quickly with 3% TFA/DCM ensures that the actual concentration of TFA is 3%).
Shake the resin in 3% TFA for 10 min.
Repeat step 3.
Wash resin with DCM (3x), DMF (3x), isopropanol (3x), and DCM (3x).
Let the resin dry in air.
多肽标记FITC方法
Reagents:
FITC
Fmoc-e-Ahx-OH
Couple Fmoc-e-Ahx-OH to the amino terminal of the peptide-resin using standard coupling conditions.
"De-Fmoc" with piperidine using the standard 20% piperidine procedure.
Wash resin with DMF (3-4x).
Swell resin with DCM and drain.
Prepare solution of 1.1 equivalent of FITC in pyridine/DMF/DCM (12:7:5). Use just enough solution to form a slurry with the resin. Do not use too much solution since the rate of the reaction is proportionate to the concentration of the solution.
Add the solution prepared in step 2 to the resin.
Let mix overnight.
Check the completion of the reaction using ninhydrin test.
If the coupling of FITC to the amino group is not complete, ninhydrin test will give a blue color. Repeat the coupling with FITC (steps 5-7) if necessary.
Wash resin with DMF (2x), isopropanol (2x), and DCM (2x).
多肽标记FAM方法
Reagent:
5-carboxyfluorescein (5-FAM)
Use standard coupling method to couple 5-carboxyfluorescein to the amino group of the peptide. For cost saving purposes, use 2x excess compared to the mmol of resin, instead of the standard 4x excess used for Fmoc-amino acids. For 0.1 mmol synthesis, use 75 mg 5-carboxyfluorescein, 76 mg HBTU, and 70 mL DIEA.
回复

使用道具 举报

药徒
 楼主| 发表于 2014-10-14 11:39:31 | 显示全部楼层
哪位朋友给翻译下啊,谢谢了
回复

使用道具 举报

药士
发表于 2014-10-14 11:43:30 | 显示全部楼层
这么简单的还用翻译呀
回复

使用道具 举报

药徒
发表于 2014-10-14 13:23:22 | 显示全部楼层
一步一来:合成生命!
回复

使用道具 举报

发表于 2018-4-10 16:13:03 | 显示全部楼层

漳州未名博欣生物医药有限公司,专业提供多肽定制合成服务!QQ:578305263
回复

使用道具 举报

发表于 2018-5-22 21:10:24 | 显示全部楼层
来看过  谢谢
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

×发帖声明
1、本站为技术交流论坛,发帖的内容具有互动属性。您在本站发布的内容:
①在无人回复的情况下,可以通过自助删帖功能随时删除(自助删帖功能关闭期间,可以联系管理员微信:8542508 处理。)
②在有人回复和讨论的情况下,主题帖和回复内容已构成一个不可分割的整体,您将不能直接删除该帖。
2、禁止发布任何涉政、涉黄赌毒及其他违反国家相关法律、法规、及本站版规的内容,详情请参阅《蒲公英论坛总版规》。
3、您在本站发表、转载的任何作品仅代表您个人观点,不代表本站观点。不要盗用有版权要求的作品,转贴请注明来源,否则文责自负。
4、请认真阅读上述条款,您发帖即代表接受上述条款。

QQ|手机版|蒲公英|ouryao|蒲公英 ( (京)-非经营性-2014-0058 京ICP证150354号 京ICP备14042168号-1 )

GMT+8, 2024-3-28 20:55

Powered by Discuz! X3.4运维单位:苏州豚鼠科技有限公司

Copyright © 2001-2020, Tencent Cloud.

声明:蒲公英网站所涉及的原创文章、文字内容、视频图片及首发资料,版权归作者及蒲公英网站所有,转载要在显著位置标明来源“蒲公英”;禁止任何形式的商业用途。违反上述声明的,本站及作者将追究法律责任。
快速回复 返回顶部 返回列表